PVC Saber bodies: 3 dollars each	Please specify silver or gold, or any other color request. Saber bodies are 1 inch in diameter, but any longer or wider saber bodies are available on request.
12 inch PVC body with flat tip
12 inch PVC body with slanted tip
11 inch PVC body with flat tip
11 inch PVC body with slanted tip
10 inch PVC body with flat tip
10 inch PVC body with slanted tip

PVC saber parts: most pieces $1.00 each	Specify silver, gold or black for all parts
1 inch PVC coupling(left on the picture of white PVC parts) This piece is made to connect two 1 inch diameter tubes together, but it can also be used as a blade shroud for a 1 inch diamter hilt.
1 1/4 inch PVC coupling
PVC endcap for 1 inch tube(middle)
PVC endcap for 1 1/4 inch tube
PVC slanted piece(right) This piece is 1 1/4 inches wide normally, but it can be ordered in bigger or smaller sizes. It can be used as part of a grip, or as a blade shroud with a slanted tip.
PVC female endcap(left on picture of black pvc) This endcap screws onto a PVC male adaptor. Specify 1 inch or 1 1/4 inch.
PVC male adaptor(right) for 1 inch diameter This piece is used to screw onto a female adaptor or a female endcap.
PVC male adaptor for 1 1/4 inch diameter: $1.50 This piece is used to screw onto a female adaptor or a female endcap.
PVC female adaptor(not shown) This piece can be seen here and here on the double-sided lightsabers. It can be used in a detachable double-sided
PVC 1 inch long ring(not shown): $0.75 This piece can be seen near the tip of the type 2 PVC double-sided lightsaber, seen here It is 1 1/4 inches wide, made to go around a 1 inch diameter tube.
PVC 1 inch long ring with slanted tip(not shown): $0.75 This piece is the end of the type 3 PVC saber, seen here.
PVC belt clip(not shown): $0.75 This is a small piece of PVC, about an inch long, and just big enough to fit around a saber. Just put it in a belt loop, and the saber can be clipped onto your belt.

Metal parts
1 inch diameter chrome tube 6 inches with flanged end: $5.00 In layman's terms : the bottom half of a type 3, 4 and 5 metal lightsaber.click here for a picture. Also used as the ends of the type 2 metal double-sided lightsaber
1 inch diameter chrome tube 12 inches long with threaded ends: $7.00 In layman's terms : The middle of a type 2 chrome double-sided saber. Click here for pictures.
1.25 inch diameter chrome tube 12 inches long with flanged end: $7.00 Used in my type 1 saber as the main body. This is the only body that a lawn sprinkler type endcap will fit in, as seen here in the type 1 metal saber.
1 inch diameter sink drain type emitter: 7.00 This is the emitter used in all of my metal sabers except for the type 2, 4 and 6. It looks good... but it's expensive, which is why the type 2 and the type 4 are cheaper than the others of the same size.
Sprinkler head endcap: $5.00 This is the endcap used in the type 1 metal lightsaber. It is a Toro 570 series 3 inch sprinkler head, if you want to buy it for yourself at your local hardware store. Although it seems like an odd choice for a lightsaber part, it ends up looking pretty good. It is not metal, but it is grouped with the metal parts because it will only fit in the 1.25 inch diameter chrome tube.
Belt loop: $1.50 as shown above, this is a silver colored D-ring attached to a flat plate that can be screwed into a saber. In order to install this, you must have a drill of some kind. Do not attempt to install without adult supervision.
Belt hook: $1.00 as shown above, this is a simple gold colored hook that can be screwed into a saber. In order to install this, you must have a drill of some kind. Do not attempt to install without adult supervision.
Clamp: $1.50 This is a small clamp used on the Type 1 metal saber, simply for decoration really. No picture for now.

Saber grip material, buttons, and assembly materials
Foam rubber: $0.50 a sheet This is the material Cheapsabers uses for most of its grips. It comes in a sheet about the size of a piece of notebook paper, and it will last for several sabers. This kind of material can be found in just about any crafts store, or even the craft section of Wal-mart.
Leather: $6.00 a sheet Soft leather for grips comes in sheets about the same size as the foam rubber. It is very comfortable to the touch, but for those who want an animal-friendly saber, this might not be for you. It comes in tan, brown or black
Leather lace: $1.00 a foot Leather lace used either for decoration, or to bind up the leather sheets used in grips. Comes in tan, brown or black.
Buttons: $0.25 each Buttons can come in red, purple, blue or clear.
Knobs: $0.75 each Knobs come in bronze or silver color.
O-rings: $2.00 for 6 These are small rubber rings that make wonderful grips. They are used on my type 3 and 4 metal saber found here.
J.B. Weld Epoxy: $5.00 This is the epoxy I use to assemble my sabers. It comes in 2 seperate tubes, and when mixed together, they will harden to incredible strength, much stronger than any glue could be. You must be careful when using it, though, if it gets on skin, wash it off as soon as you are done. It takes 15 hours to completely harden, so the sabers must sit overnight if you use this kind of epoxy to assemble them. There is enough in this tube to use for a few sabers.

     Once you have finished your kit, click below to add in the shipping costs.

If you have ordered any of the metal or PVC main saber body parts, click here to add 5 dollars to shipping.

If you have ordered more than 2 parts, but have not ordered any metal or PVC tubes, click here to add 3 dollars for shipping.

If you only ordered 1-2 parts that are not metal or PVC tubes, click here to add 1 dollar for shipping.